You watch may also stop If your watch hands have become bent or are not seated properly. If the alignment is ‘off’ then the watch can become overbanked and stop running for periods of time. Improper alignment can impact how a pocket watch works as your timepiece relies on very delicate precision. Jewels will often stay in place even after they are broken which will allow the watch to run for a short time before stopping. If this is the case it needs to be examined by a watchmaker.Ĭracked or broken jewels can also be responsible for the watch not moving. If your watch is working correctly in certain positions, the balance staff pivots could be bent or broken or the hairspring could be rubbing against another part of the watch. If your pocket watch is fully wound, ticks but then stops working there are several possible causes. Scenario 4: My pocket watch ticks but then stops If your watch has been wound but still does not tick, it’s more likely that it is one of the other scenarios within this guide that’s the problem. Whilst over winding a watch is not healthy for the timepiece, more often than not there’s something else at play. When a pocket watch starts to show signs of working incorrectly, most owners immediately believe that the watch has been overwound. Scenario 3: Is my pocket watch overwound? The easiest way to remedy this is to take it to a watchmaker who will be able to adjust the sleeve to the proper height. If the height of the sleeve is not correct, the watch can start to experience winding issues or slip back into ‘setting mode’. If you own a pendant set watch you may find that the pendant sleeve determines the position of the stem. Scenario 2: What to do when a pocket watch slips into ‘setting mode’ In this instance, the mainspring simple needs to be replaced. If it is the mainspring you will feel slight resistance when you’re winding the watch along with quiet ‘pops’ every so often that seem to release the tension. The first is due to a broken winding mechanism which should only be fixed by a professional watchmaker, the second is a broken mainspring. There are two common reasons why a pocket watch will not wind properly. Scenario 1: My pocket watch does not wind fully In this blog, we’re going to look at some of the most common issues that pocket watch owners face and how you can tackle them. We will of course review these updates and revisit our support plans at that time.With all mechanical devices, it’s imperative that you take the time to check your timepiece to make sure that it’s working correctly, however, keeping your pocket watch in good working order doesn’t have to be taxing. There can be little doubt that Microsoft is aware of these issues and will address them as future version updates. WE RECOMMEND RUNNING TIMER PRO ON OFFICE 2010 32 BIT. Given the issues reported in the 64 bit version of Office 2010 in Excel Macro handling area and the complete lack of support for older PDA devices:ĪT THIS TIME WE ARE NOT PLANNING ON PUTTING THE DEVELOPMENT RESOURCES INTO MAKING TIMER PRO COMPATIBLE WITH THE CURRENT OFFICE 2010, 64 BIT BUILD. We have limited development resources and have outlined above the plans that we believe will add significant add value to all clients use of Timer Pro. We estimate that the lack of ability to support older Pocket PC operating systems would directly impact over 400 of our registered users. The support for Pocket PC is available in the 32 bit version. In addition Microsoft has provided no support for Pocket PC operating system other than Windows Mobile in the 64 bit version of the operating system. Our tests also indicate that the macros also work inconsistently compared to the 32 bit version of Excel. While many issues are raised in the 64 bit version of Office that you may wish to consider, in Timer Pro the main areas of impact that we have identified so far is that the 64 bit version of Excel 2010 handles macros differently than previous versions. Given our current evaluation we have to agree with this assessment. Office 2010 64-bit has all of the hallmarks of a traditional Microsoft “version 2.0” product - it works, but not like it should, and it doesn’t play well with others. Here is a synopsis on its impact on Timer Pro: Please see the following article that summarizes the current situation: 64 bit computing is certainly the future but it may take some time to stabilize the environment. Basically 32 bit computing has been around for many years and is a stable environment – XP is a 32 bit operating system. Timer Pro will run on Windows 7 both 32 and 64 bit configurations.īy default, Microsoft Office 2010 installs the 32-bit version of Office 2010 even if your computer is running 64-bit editions of Windows.Īs background, Microsoft Office 2010 for Window 7 offers the option of support for 32 bit or 64 bit operation. We are aware that many clients are upgrading from XP to Windows 7.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |